the common fault of the automatic aluminum foil sealing machine is that it is connected to the switching power supply. the indicator light of the hand-held aluminum foil sealing machine does not light up. in fact, this cannot become a common fault. in most cases, only the power cord plug is not plugged in. therefore, you only need to check whether the power plug is plugged in. the second type of common fault is that the data signal indicates that everything is normal during work, but it cannot be sealed. this type of common problem has the following many reasons:
1. insufficient heating time; if the heating time is insufficient, then you only have to increase the heating time and increase the output power of the sealing.
2. the sensing film is not matched with the utensil material; to deal with this common fault, only the matched sensing film can be used.
3. the heating time is too long; the same solution is to reduce the heating time and reduce the sealing output power
the fourth type of common problem is that the magic hair wrinkles are induced after sealing, and the cork is melted. this common fault is generally caused by too long heating time, so only need to reduce the heating time, and the output power of the sealing can be effective.
the above are all common faults that are common in the entire application process of the hand-held aluminum foil sealing machine. the solutions to this common fault are all very simple, but everyone is often a little at a loss when encountering such common faults. in addition, i don't understａnd the common faults, so i can't find the common faults and deal with the common faults.
common problem.
there are several common problems in the whole process of applying the hand-held aluminum foil sealing machine:
1. the hand-held aluminum foil sealing machine uses single-phase three-wire power plugs. for the safety of operators, single-phase three-wire power plugs should be used as much as possible. the road surface of the workplace must be dry to maintain the insulation layer.
2. enter the power supply voltage and everything is normal. if the power supply voltage is less than 160v, stop working and wait until the working voltage is normal.
3. the hand-held aluminum foil sealing machine is not suitable for stainless steel containers and metal material corks and its electrochemical aluminum spray caps. it is strictly forbidden to press the heating button on the surface of the metal material table, otherwise it will destroy the equipment, such as touching metal material corks and electrochemical aluminum for spraying caps, the aluminum and platinum sealing can be carried out first, and then the bottle stopper can be screwed on
4. in the whole process of application of the hand-held aluminum foil sealing machine, the actual operating staff should always pay attention to the heating condition of the induction head, such as when the touch is overheated (up to 80 ℃), stop working, and wait until the induction head is of course cooled or used the electric fan points to the sensor head for forced and rapid cooling, so that the temperature of the sensor head is reduced to the indoor temperature (around 25°c) before starting to work, to prevent the sensor head from being damaged due to excessive temperature
5. before turning on the switching power supply, be sure to insert the induction head into the induction aviation socket and clamp the screw cap
6. you should always check the color tone of the milky white bakelite board in front of the induction head. in this situation, the induction head or induction solenoid coil should be replaced immediately to prevent the server from destroying the server again.
7. when the total area of the induction aluminum platinum is too large, after pressing the induction power switch, the time display will immediately reach zero. there is no induction or the bright red overcurrent indicator light flashes and is accompanied by the di alarm sound. it may be possible to expａnd the distance between the sealed object and the sensor head before all normal work can be carried out. objects such as rubber sheets can be used as barriers, and metal composite materials should not be used instead.
8. the hand-held aluminum foil sealing machine has a temperature over-temperature automatic maintenance function. when the temperature inside the machine is over-temperature, the emerald green over-temperature indicator light is on. at this time, it should be turned off and the internal refrigeration or the signal light will be off and it can work again immediately middle
9. the material selected for the induction aluminum-platinum film must be the same as the material of the vessel to be sealed.